How to Build a Basic Garden Bench

How to Build a Basic Garden Bench

Inspired by a French antique, this colorful bench has a modern simplicity—and easily seats two. Solid stain gives the stock pine lumber an added layer of protection from the elements.

Its soft green blends in with verdant surroundings, but you could also go bolder with red or yellow to add contrast.

[external_link_head]

Steps for Building a Garden Bench:

Follow these directions for building your DIY garden bench.

Step 1: Cut the Boards to Length

How to Build a Basic Garden Bench

Using a miter saw and the cut list above, cut the 2×12 board to size to create the seat, stringer and leg pieces. Cut the 1×3 board to length to create the trim pieces.

[external_link offset=1]

Step 2: Mark the Detail on the Legs

How to Build a Basic Garden Bench

On the leg pieces, measure and make a mark along the bottom edge 4 inches from each side. Make an additional mark 5½ inches from the base of each leg, centered on the width of each board. Draw lines between the marks to create the outline of the triangular cutouts.

See also  Timber Garden Edging [Ideas, Tips and Pictures] – Garden Tabs

Step 3: Cut the Detail on the Legs

How to Build a Basic Garden Bench

Using a jigsaw, cut the outline marked in Step Two. (Tip: For a straighter cut, first cut the lines with a circular saw, and then finish cutting the tip of each notch with a jigsaw.)

Step 4: Size the Stringer

How to Build a Basic Garden Bench

Using a circular saw, rip 3¼ inches from the width of the stringer. (Note: you can also leave this board as full width, though the stringer will hang lower to the ground between the legs for a more hefty look.)

Step 5: Add the Stringer between the Legs

How to Build a Basic Garden Bench

Apply wood glue to the ends of the 2×12 stringer. Position the board on edge between the legs with the trimmed edge flush with each top edge of each leg. Drill two pilot holes through each leg and into the ends of the stringer. Drive 3-inch wood screws through the pilot holes and into the stringer to secure the pieces.

See also  A beginner’s guide to gardening

Step 6: Attach the Seat to the Base

How to Build a Basic Garden Bench

Apply wood glue to the top of the legs and stringer. Position the seat board flat on the base flush with its sides, and with equal overhang of 4½ inches on each end. Drill two pilot holes through the seat and into each leg and three pilot holes through the seat and into the stringer. Drive 3-inch deck screws through the seat and into the legs and stringer.

[external_link offset=2]

Step 7: Prep the Seat Trim

How to Build a Basic Garden Bench

Make a mark on each end of the 1×3 trim pieces that’s 1½ inches from the top edge. Using the mark as a guide, clip the rest of the bottom corner at 45-degrees on the miter saw.

Step 8: Attach the Seat Trim

How to Build a Basic Garden Bench

Apply wood glue to the sides of the 2×12 seat. Position the trim flush with the top edge of the seat, and with the clipped corners facing downward. Drill three pilot holes through each trim piece, and then connect the trim to the seat using 2-inch screws.

See also  Tea Bags As Fertilizer – Tips On Using Tea Bags In Compost

Step 9 : Apply the Finish

How to Build a Basic Garden Bench Jenn Largesse

Fill all the screw holes with exterior-grade wood filler. Sand the assembly smooth. Apply two coats of exterior wood stain and let dry before use.


What You Need for This Project:

How to Build a Basic Garden Bench

Materials

  • 2x12x10’ Board
  • 1x3x6’ Board
  • Exterior Wood Glue
  • 3-inch Exterior Deck Screws
  • 2-inch Exterior Deck Screws
  • Exterior Wood Filler
  • Sandpaper
  • Exterior Wood Stain

Cut List

  • 2×12 Seat – 1 @ 42 inches
  • 2×12 Stringer – 1 @ 30 inches
  • 2×12 Legs – 2 @ 16½ inches
  • 1×3 Trim – 2 @ 42 inches

Tools:

[external_footer]