If you’ve ever tried to sleep near a sink that just won’t stop ’drip, drip, drip, dripping’, you know how annoying it can be.
But a leaking tap is also wasteful, expensive, and potentially damaging. The good thing is all you need to do in most cases is to replace the tap washers.
You're reading: How To Change A Tap Washer (12 Easy Steps)
Before we jump in some of you may be wondering, what is a tap washer? Washers are small disks that sit inside the tap to create a seal when turned off. They do wear over time which results in leaking taps. It’s possible your taps are washerless, but these types of taps are far less likely to leak.
One more question before you start – Do you need a plumber? If you get to the bottom of this article and you don’t think ’Bob’s your uncle. Fixing a leaky tap is a piece of cake!’, then you might want to call a plumber to fix your leaking tap instead.
Washers are general wear and tear product, replacing a washer should be done every 1-2 years. And if your taps are old, replacing them with newer ones can save on your water bill! So, learning how to change a water tap washer is a fantastic skill to have.
Ok, let’s go through the steps for changing a tap washer!
Step 1. Grab your tools
Got a toolkit in the shed with a few spanners, pliers, screwdrivers and a rag? You’re ready to go!
Step 2. Turn off the water supply
Whatever you do, don’t start messing with those pipes until you turn off the water at the mains. Unless you want an almighty mess to deal with. You’ll probably find the mains out the front with the water meter, turn this until the water supply has been successfully turned off.
Step 3. Empty the pipes
But even when the mains is off, you should still open that dripping tap up to empty the pipes that feed into it. If it stops pretty quickly, the mains were successfully turned off and you’re ready to rumble. You can now continue changing the old washer without causing damage.
Read more: How To Freeze Chives The Simple & Easy Way
Step 4. Remove the tap button
Next, you’re going to get the tap off so you can access that busted tap washer. The tap might have a button on the top that holds the handle on – it might be the part that identifies the ’hot’ or ’cold’ water. If it is round or inset, pop it off gently with a screwdriver. Otherwise, you may need a spanner.
Be gentle when taking this off to prevent damage to your kitchen or bathroom sink.
Step 5. Remove the handle
Now you’re going to take the tap handle off, and – depending on the type of tap. It’s probably as simple as sliding or screwing it off to reveal the inner workings of the tap that lies beneath. There are many types of taps often used in Sydney homes, the washer used may be different depending on your tap.
Step 6. Remove the tap skirt
If you see a metallic skirt or shroud on the tap, that will be coming off as well. This could be where you need the pliers because some plumbers will have secured them with a sealant.
Step 7. Remove the tap bonnet
Now, you’re going to unscrew the actual body (or headgear) of the tap, which will reveal the plastic or brass jumper valve within. You’ll need a spanner or shifter for this.
Step 8. Remove the washer
Once this jumper valve is taken off, and now you’re all ready to remove that pesky rubber tap washer. If it’s out of reach, some pliers with a handy needle nose will work just as well as a pair of tweezers. If it’s a typical washer problem, you might see a split.
Step 9. Replace the washer
Now you’ve got that washer in your hot little hands, it’s time for a trip to the hardware store for a new tap washer. If the jumper valve looks undamaged, you could get away with only replacing the broken washer. But make sure you take both parts to the shop with you so you get the right ones.
Step 10. Put it back together
With the new washer and jumper valve in place, it’s time to put everything back together again! Screw the tap bonnet on and tighten with that spanner and then proceed to put the rest of the tap back together in the reverse order to how you took it apart.
Step 11. Get that water flowing
When back together, close the tap completely before turning the mains water back on. When the mains is back on, test the tap a few times and check that the leak is completely fixed. Turn the tap on for a couple of minutes to clear out any unwanted debris.
Step 12. Celebrate wildly
If everything has gone to plan you’ve changed the tap washers and stopped the tap leaking. You can also replace the sink drain. Well done, you’re a pretty handy DIY plumber after all! If you are experiencing no hot water, this may be a different issue.
But if you tried to change a tap washer and it hasn’t all gone smoothly, don’t beat yourself up – help is on the way.
Fixed Today are absolute experts in the field of tap repairs and replacements. We can also help with leaky showers or taps that are noisy or hard to turn on or off.
In other words, all your Sydney plumbing problems can be Fixed Today! Get in touch on +61404532026 or send us an email today.
News & Updates Latest Blog Posts
July 12, 2021
Read more: How to Make a Zen Garden
How To Dispose Of Cooking Oil
Looking for ways to dispose of your cooking oil that won’t damage your pipes and plumbing? Read along with us to find out!
July 12, 2021
When To Replace Your Hot Water System
Are you wondering if it’s time you replace your hot water unit? We have put together this guide on the signs you should know!
June 10, 2021
Why Does My Toilet Keep Running And What Can I Do About It?
Does your toilet keep running or trickling after you flush? We have created a guide to help you figure out why and how to stop it!
June 01, 2021
Plumbing Problems You Shouldn’t Try To Fix Yourself
There are some plumbing issues that are best left to the professionals. We have outlined which plumbing problems you are best not to do yourself.
* All coupons & discounts are limited 1 per person & apply to paying jobs only.
© Copyright Fixed Today Plumbing Sydney +61404532026
ABN: +61404532026 – License: 305428C
Made with ♥ in Australia
Website by sitecentre